To use the BCF2000 Template, you must first download the sysex file of all the presets into the BCF2000 unit. You can dump this file with any midi sysex dump utility program like Midi-Ox, or something similar. Save this to a single preset in the unit. Make sure that preset is the selected preset on the unit. Multiple BCF2000 units may be used up to 4 units for a total of 32 faders.
To do this, you must download each of the respective sysex files to the 4 units and make sure you label them somehow to connect them in the proper order from 1 thru 4.Connecting multiple units is done as follows:-
Unit 1: USB-4 mode; Out A to Unit 2 In
Unit 2: Stand-Alone 4 mode; Out B to Unit 3 In; Out A back to Unit 1 In if only 2 units, otherwise Out A to a Midi Merge box In
Unit 3: Stand-Alone 4 mode; Out B to Unit 4 In; Out A to the Midi Merge box In
Unit 4: Stand-Alone 4 mode; Out A to the Midi Merge box In
The Midi Merge box Out must be connected back to Unit 1 In.With the use of a Midi Merge box for more than 2 units, you may experience fader glitching and odd behaviour if grabbing more than one fader at the same time across separate units. This can be caused by the merge not keeping individual NRPN data strings together from each unit. This can be solved with the use of some virtual mergers, like MidiOX - Midi Yoke, which give you the option to lock NRPN strings together, keeping the full data packet from being interrupted midstream.If the Mixer Views to Hardware Controller navigation link is active, the surface will chase SAWStudio's Hot Track selection.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Connecting BCF2000's
First the relevent SAW/SAC file (SAC/SAW BCF2000 midi control extended template (8 ch.,16 ch. or 24 ch.) needs to be sent via sysex to each BCF2000 if more than 1 is being used.
Load the desired template into MidiOx or similar and send to the BCF2000.
Ensure the display lights up and the LEDS run around the perimeter.
This d/l should take about 1 minute.
Go to XP control panel/System/Hardware/Device Manager/USB Controllers and ensure
a USB Composite Device is listed. If it is, click on it and BCF2000 should be shown.
If it's not listed then there's an OS recognition problem.
When the sysex has finished, save it to a BCF2000 preset, e.g. P1
---------------
Set BCF2000 - press/hold Edit - press Store.
Turn top left data knob to read u1 for single unit.
For multi template use u4 on controller 1 and s3 on controller 2 & 3.
USB connects to unit 1 only.
Midi cables go OUT A Unit 1 to IN unit 2.
OUT B Unit 2 to IN Unit 1.
--------------
Make sure your mct file is in the SAC Configuration Folder.
Open SAC.
Goto File/Midi Control Template File.
Open BCF2000 8ch. mct.
Goto Options/Midi Device and select USB Audio Device in both MC Device In and Out.
Goto SMPT/Midi and tick Midi Control In Active and MC Out Active.
-------------
[ 本帖最后由 himhui 于 11-2-10 14:45 编辑 ]
To do this, you must download each of the respective sysex files to the 4 units and make sure you label them somehow to connect them in the proper order from 1 thru 4.Connecting multiple units is done as follows:-
Unit 1: USB-4 mode; Out A to Unit 2 In
Unit 2: Stand-Alone 4 mode; Out B to Unit 3 In; Out A back to Unit 1 In if only 2 units, otherwise Out A to a Midi Merge box In
Unit 3: Stand-Alone 4 mode; Out B to Unit 4 In; Out A to the Midi Merge box In
Unit 4: Stand-Alone 4 mode; Out A to the Midi Merge box In
The Midi Merge box Out must be connected back to Unit 1 In.With the use of a Midi Merge box for more than 2 units, you may experience fader glitching and odd behaviour if grabbing more than one fader at the same time across separate units. This can be caused by the merge not keeping individual NRPN data strings together from each unit. This can be solved with the use of some virtual mergers, like MidiOX - Midi Yoke, which give you the option to lock NRPN strings together, keeping the full data packet from being interrupted midstream.If the Mixer Views to Hardware Controller navigation link is active, the surface will chase SAWStudio's Hot Track selection.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Connecting BCF2000's
First the relevent SAW/SAC file (SAC/SAW BCF2000 midi control extended template (8 ch.,16 ch. or 24 ch.) needs to be sent via sysex to each BCF2000 if more than 1 is being used.
Load the desired template into MidiOx or similar and send to the BCF2000.
Ensure the display lights up and the LEDS run around the perimeter.
This d/l should take about 1 minute.
Go to XP control panel/System/Hardware/Device Manager/USB Controllers and ensure
a USB Composite Device is listed. If it is, click on it and BCF2000 should be shown.
If it's not listed then there's an OS recognition problem.
When the sysex has finished, save it to a BCF2000 preset, e.g. P1
---------------
Set BCF2000 - press/hold Edit - press Store.
Turn top left data knob to read u1 for single unit.
For multi template use u4 on controller 1 and s3 on controller 2 & 3.
USB connects to unit 1 only.
Midi cables go OUT A Unit 1 to IN unit 2.
OUT B Unit 2 to IN Unit 1.
--------------
Make sure your mct file is in the SAC Configuration Folder.
Open SAC.
Goto File/Midi Control Template File.
Open BCF2000 8ch. mct.
Goto Options/Midi Device and select USB Audio Device in both MC Device In and Out.
Goto SMPT/Midi and tick Midi Control In Active and MC Out Active.
-------------
[ 本帖最后由 himhui 于 11-2-10 14:45 编辑 ]
應該也就是把 C:\SAC\Configuration 下的 MidiCtrl_Behringer_BCF2000_8-Ch.mct 用midiOX 或 midiYOKE 傳到 第一台 bcf2000, MidiCtrl_Behringer_BCF2000_16-Ch.mct 傳到 第二台bcf2000, MidiCtrl_Behringer_BCF2000_24-Ch.mct 傳到第三台bcf2000, MidiCtrl_Behringer_BCF2000_32-Ch.mct 傳到第四台bcf2000.....
观众反应
