- 第 1 页 -
稳定的跳线软件！Synchronous.Audio.Router.WiN.x64.FREE
SynchronousAudioRouter
ok, but what is it?
how use?
what's it cost?
The cause of, and solution to, all your audio problems.
ok, but what is it?
Put simply, Synchronous Audio Router lets you route audio from any Windows application through a DAW (digital audio workstation) application, giving you an immense amount of control over your system's audio. You can apply sophisticated effects, routing and switching, and combine the audio streams from each individual application any way you want, producing any number of output mixes.
If your applications of choice don't let you select an audio device, SAR has you covered: you can define per-application routing rules which will override the Windows default audio device settings. You can even use pattern matching to define rules for groups of applications.
It's also fast. SAR operates inline with your existing ASIO driver, adding no additional buffer latency to your DAW, and uses WaveRT for direct low latency transport of audio between applications. This is in contrast to many other "virtual audio cable" type drivers which often require buffer sizes as large as 50-100ms to work reliably.
how use?
You need 3 things: the SAR driver, an ASIO driver for your sound card (if it's good, it came with one, otherwise get ASIO4ALL), and DAW software. If you don't already have a DAW, use REAPER. If you do, I assume you don't need me telling you how to set it up, so have fun.
Once you've installed all the prerequsites, watch some videos:
- SAR tutorial part 1: Setting up REAPER
- SAR tutorial part 2: Application routing rules
- SAR tutorial part 3: Creating multiple mixes
- SAR tutorial part 4: Creating a delay mix
- SAR tutorial part 5: Equalization, compression and gating
If you prefer text, check out the SAR user manual.
what's it cost?
Nothing. SAR is free software, distributed under the GNU General Public License, version 3 or later.
[官方网站]
SAR.AUDIO
[简介]
一款完整代替Asio Link Pro的软件，稳定、简单、且modern.
可实现DAW输出到应用程序，应用程序输入到DAW。
[优点]
支持多声道环绕声和立体声；
支持分进程路由，例如游戏和网易云音乐；
完全免费；
稳定性非常高，我用了很久没有爆音；
无限输入和输出；
当关闭DAW或者切换ASIO声卡时，自动释放多余的虚拟通道设备，避免系统设备界面显示杂乱，影响效率；
路由功能完全由DAW决定，它只添加输入和输出虚拟通道，无需学习成本；
[系统兼容性]
仅限Windows X64系统；
Linux下使用Jack代替；
Mac下使用Loopback代替；
[下载地址]
自行下载MSI安装包进行安装。
PlayBack就是系统的喇叭；Recording就是系统的麦克风，添加完成后在DAW会有对应的输入和输出。比如我添加一个PlayBack叫BrocastIn作为YY上别人连麦的本机输出设备，那么我可以新建一个音轨，添加一个输入，就叫BrocastIn（输出对应的输入会被自动建立）。也可以添加一个PlayBack:AppsOut，DAW监听网易云的伴奏，同时和我们的人声一起发送到MicOut给软件，就可以实现监听连麦、只发送人声和伴奏，解决卡麦问题。
图下是我彩虹六号的路由设置，其实没卵用，因为R6又不能当直播平台用。
注意因为WaveRT要求，延迟必须控制在10ms以内，否则会导致转发时缓冲区欠载，具体缓冲区大小一般设置为128即可，具体要根据声卡ASIO性能分析。
观众反应
yzjb 发表于 19-7-27 12:34
谢谢分享，还是习惯用asiolinkpro 2.4.4图形话设置，连线清楚一目了然。
我还是喜欢REAPER的路由矩阵
liu657836036 发表于 19-7-29 11:01
请问支持所以声卡吗？Avid Mbox 3 USB声卡支持内放直播吗？单麦全民k歌录歌出来只有一个声道有人声问题能解 ...
只需要你在DAW里面的INPUT设置为L或者R就可以了，如果你选的是L+R之类的只有一个声道。