如没记错, 可以加一个 JMS 出品的 plugin支持外部硬件效果器。
另外有一些连接可参考:-
http://translate.google.com/tran ... 6hl%3Dzh-CN%26lr%3D
[ 本帖最后由 himhui 于 2005-11-5 16:31 编辑 ]
另外有一些连接可参考:-
http://translate.google.com/tran ... 6hl%3Dzh-CN%26lr%3D
[ 本帖最后由 himhui 于 2005-11-5 16:31 编辑 ]
對, 但錄下來好像還需方法...正在找...不過你也可先試試
或先看看這個, 可以在國內google找到翻譯本:-
http://www.sawstudiouser.net/for ... ght=external+reverb
[ 本帖最后由 himhui 于 2005-11-5 17:01 编辑 ]
或先看看這個, 可以在國內google找到翻譯本:-
http://www.sawstudiouser.net/for ... ght=external+reverb
[ 本帖最后由 himhui 于 2005-11-5 17:01 编辑 ]
There you can pick mono or stereo devices for a source... you also can pick any mixer channel for a source... pick mixer chan 3... and the track will record whatever is on that mixer channel... in your case... it should be the reverb return from the external unit.
[ 本帖最后由 himhui 于 2005-11-5 19:48 编辑 ]
[ 本帖最后由 himhui 于 2005-11-5 19:48 编辑 ]
JMS AUDIO
Buss Extention and Send/Receive Module(免费软件) http://www.jms-audioware.com/jmsbuss.htm
我没有用硬件, 你得试试
Buss Extention and Send/Receive Module(免费软件) http://www.jms-audioware.com/jmsbuss.htm
我没有用硬件, 你得试试
saw is the only software that can do hardware inserts with NO incurred latency (yes, nuendo/logic/pt do hardware inserts, but with latency. though nuendo and logic I beleive compensate, this adds to engine latency). this is a very very amazing thing from an industry perspective. Maybe more understandable to prospective customers than most of saw's other amazing features.
saw是唯一软件在用硬件插入时没有引起延误。
saw是唯一软件在用硬件插入时没有引起延误。
原来如此
you can setup an Aux Send Master to send data out to any of the soundcard outputs... take the Aux Send Master Out Assign off of Virtual and set it to a device out... then you can do the same for the Return underneath it... take its Input Source off of virtual and set it to a device in...
Loop the device out and in that you assigned through your external processing gear and you are all set.
Make sure to assign the Return track into the mix bus (usually out 1)... when you play, you should hear all channel signals sent to the aux send routed thru your effects box live during playback.
The only thing to realize here is that you can no longer build mixes because the effect must be processed in realtime since it is hardware... so you do mixdowns the old fashioned way of playing the entire session and capturing the results on a 2-track tape or DAT or looping the signal back to SAWStudio and recording live on another track.
No delay in SAWStudio... the engine is is a split design when routing through the aux sends and returns as I described... the aux data goes out ahead of the MultiTrack data so the return signal can then be automatically resynced... live in realtime... try it... use large buffers and watch the Aux Master meters... you will notice that they are ahead of the the regular channel meters... the result is no delay or latency between the straight and processed signal through the external devices.
This was one of the first design elements perfected in the SAWStudio engine... long before the ability to do small buffer sizes was possible.
设置硬件 aux send master 的 out 到 sound card 的输出, 然后在saw的aux send master 的 out assign 选真实的device out, 再在 return 下的 input source 选真实的 device in....这样便将硬件输入,输出串连, 搞定。因为是硬件, 故不过不能 buildmix, 只能录。
[ 本帖最后由 himhui 于 2005-11-5 20:15 编辑 ]
you can setup an Aux Send Master to send data out to any of the soundcard outputs... take the Aux Send Master Out Assign off of Virtual and set it to a device out... then you can do the same for the Return underneath it... take its Input Source off of virtual and set it to a device in...
Loop the device out and in that you assigned through your external processing gear and you are all set.
Make sure to assign the Return track into the mix bus (usually out 1)... when you play, you should hear all channel signals sent to the aux send routed thru your effects box live during playback.
The only thing to realize here is that you can no longer build mixes because the effect must be processed in realtime since it is hardware... so you do mixdowns the old fashioned way of playing the entire session and capturing the results on a 2-track tape or DAT or looping the signal back to SAWStudio and recording live on another track.
No delay in SAWStudio... the engine is is a split design when routing through the aux sends and returns as I described... the aux data goes out ahead of the MultiTrack data so the return signal can then be automatically resynced... live in realtime... try it... use large buffers and watch the Aux Master meters... you will notice that they are ahead of the the regular channel meters... the result is no delay or latency between the straight and processed signal through the external devices.
This was one of the first design elements perfected in the SAWStudio engine... long before the ability to do small buffer sizes was possible.
设置硬件 aux send master 的 out 到 sound card 的输出, 然后在saw的aux send master 的 out assign 选真实的device out, 再在 return 下的 input source 选真实的 device in....这样便将硬件输入,输出串连, 搞定。因为是硬件, 故不过不能 buildmix, 只能录。
[ 本帖最后由 himhui 于 2005-11-5 20:15 编辑 ]