都可以, 不過應該 Frontier AlphaTrack 較好
Frontier Design AlphaTrack (Top)
The Frontier Design AlphaTrack is a usb connected remote controller with a full sized fader in a small box.
The LCD display is used to show parameter and channel labels in the various selection modes.
If the Mixer Views to Hardware Controller navigation link is active, the surface will chase SAWStudio's Hot Track selection.
F Make sure your controller is set to Native Mode (TaskBar Icon) to ensure compatibility with this template.
F Using the Shift Mode does not require you to hold down the Shift Button. Just press it once and it will engage and light up to show that Shift Mode is active. You can cancel Shift Mode by pressing the button again. Most commands that use Shift Mode will automatically disengage it after the command is executed.
Controller Surface SAWStudio
Fader Control mixer channel faders. Can operate Input, Return, and Output channels based on track / channel select switches. Touching and adjusting the fader will automatically switch the LCD to Fader Mode and display the fader data.
Shift Button Toggles Shift Mode on / off. Using the Shift Mode does not require you to hold down the Shift Button. Just press it once and it will engage and light up to show that Shift Mode is active. You can cancel Shift Mode by pressing the button again. Most commands that use Shift Mode will automatically disengage it aftter the command is executed
Rec Button Toggles the record meter open/close for the current track.
?Shift Mode: Operates the record meters as a record template, allowing multiple channels to be armed or disarmed at once.
Solo Button Toggles Solo on and off for the current channel.
?Shift Mode: Toggles all active solos off.
Mute Button Toggles Mute on and off for the current channel.
Left or Right Parameter Knob Either of these knobs act as a function selector, scanning through different control types. Use the left or right knob, depending on whether you are left or right handed so you do not cover up the display as you turn the knob.
The current selectable control types are: Layer; Fader; Pan; Aux 1 In; Aux 1 Pst Fdr; Aux 1 Lvl; Aux 1 Pan; Aux 2 In; Aux 2 Pst Fdr; Aux 2 Lvl; Aux 2 Pan; Aux 3 In; Aux 3 Pst Fdr; Aux 3 Lvl; Aux 3 Pan; Aux 4 In; Aux 4 Pst Fdr; Aux 4 Lvl; Aux 4 Pan; Aux 5 In; Aux 5 Pst Fdr; Aux 5 Lvl; Aux 5 Pan; Aux 6 In; Aux 6 Pst Fdr; Aux 6 Lvl; Aux 6 Pan; Comp In; Comp Gn; Comp Thr; Comp Ratio; Comp Rel; Comp Att; Gate In; Gate Rvs; Gate Thr; Gate Flr; Gate Rel; Gate Att; Dyn Key Listen; Dyn Eq Lo; Dyn Eq Hi; Dyn Key; Eq In; Eq LoCut In; Eq LoCut Frq; Eq HiCut In; Eq HiCut Frq; Eq Gn 1; Eq Frq 1; Eq Q 1; Eq Gn 2; Eq Frq 2; Eq Q 2; Eq Gn 3; Eq Frq 3; Eq Q 3; Eq Gn 4; Eq Frq 4; Eq Q 4; Eq Gn 5; Eq Frq 5; Eq Q 5; Mono; Swap LR; Phase Rvs; Attenuator; MultiTrack Position
The LCD dislays the currently selected type and value.
Center Parameter Knob This knob adjusts the value for the currently selected control type. If the current type is the MultiTrack Position display, this knob has no effect and the position is adjusted by the various transport controls and touch strip.
Pressing the knob as a switch sets the control to the default value.
?Shift Mode: For Aux_Lvl control types sets the control to -inf.
Pan Button Switches the Control Type to Pan for the current channel. The Pan LED lights when in Pan Mode.
Send Button Switches the Control Type to Aux_Lvl_1 for the current channel. Repeated pressings switch to Aux_Lvl_2, Aux_Lvl_3, Aux_Lvl_4
, Aux_Lvl_5, Aux_Lvl_6, and then back around to the beginning. The Send LED lights when in Aux Mode.
EQ Button Switches the Control Type to Eq_In for the current channel. Repeated pressings switch to Eq_Lo_In, Eq_Hi_In, Eq_Gain_1, Eq_Gain_2, Eq_Gain_3, Eq_Gain_4, Eq_Gain_5, and then back around to the beginning. The EQ LED Lights when in Eq Mode.
Plug In Button Activates and opens (if needed) the FX_Pre and FX_Pst views. If the current Hot Track is an Output track, it also activates the Final Res patch view.
?Shift Mode: Closes all FX patch views.
F1 Button Jumps to Locate Point 1.
?Shift Mode: Sets Locate Point 1.
F2 Button Jumps to Locate Point 2.
?Shift Mode: Sets Locate Point 2.
F3 Button Jumps to Locate Point 3.
?Shift Mode: Sets Locate Point 3.
F4 Button Jumps to Locate Point 4.
?Shift Mode: Sets Locate Point 4.
Track < Button Decrements the Track / Channel.
?Shift Mode: Marks the begin position. When any marked area is active, the LCD displays a small mark in the top right corner.
?Ctrl Mode: Set by pushing the left or right parameter knob. Lights both track button LEDs and jumps down one section from Output to Return to Input channels.
Track > Button Increments the Track / Channel.
?Shift Mode: Marks the end position. When any marked area is active, the LCD displays a small mark in the top right corner.
?Ctrl Mode: Set by pushing the left or right parameter knob. Lights both track button LEDs and jumps up one section from Input to Return to Output channels.
Loop Button Toggles AutoRewind on and off. When active, regular MT playback will jump back to the starting point when playback is stopped. If there is an active marked area, MultiTrack playback will continue to loop the marked area.
?Record Mode: Toggles AutoRecord Loop Mode on and off. SRP recordings will continue to create new takes of the marked area, looping back to the cursor position pre-roll starting point.
?Record-Shift Mode: Toggles AutoRecord Layer Loop Mode on and off, which fills layers with new takes on the Lite and Full SAWStudio versions.
Flip Button Switches the Control Type to MultiTrack Position. The LCD now displays Timeline position information in the current Timeline display mode. Pressing the button again switches the Control Type back to the previous type selection.
Transport Rewind Button Moves the current cursor position back 10 seconds on the timeline. This function will auto-locate the playback if active.
?Shift Mode: Jumps to the session home position.
Transport Fast Forward Button Moves the current cursor position forward 10 seconds on the timeline. This function will auto-locate the playback if active.
?Shift Mode: Jumps to the session end position.
Transport Stop Button Stops playback, record and live input operations.
?Shift Mode: Saves and updates the session edl.
?Msg / Dialog Mode: When a message dialog box is active, acts as a cancel or "no" response. The LCD will display many important messages directly.
Transport Play Button Starts MultiTrack play or SRP play operations.
?Shift Mode: Activates Live Mode.
?Msg / Dialog Mode: Acts an Okay, Yes, or Enter response.
Transport Record Button Starts a multitrack record operation or punches in during SRP play mode.
?Shift Mode: Starts a RecRdy operation.
Touch Strip Acts as a position shuttle which adjusts the MultiTrack cursor position. When first touched, the Flip button is activated and the LCD will display the cursor position.
FootSwitch Jack Toggles Playback on and off.
?Record Mode: Toggles Punch-In and Punch-Out during an SRP operation. Does a Punch-In on a straight Record operation.