如果你用 Sam 刻 CD 的话，赶快来升级吧。下载；
http://www.samplitude.de/patches/Patch_CDR_DLL_27022_E.exe
==============================================================================
-- PoINT CDR Dlls for MAGIX software --
-- --
-- --
-- Runtime Modules --
-- Version 2.7.022 --
-- (June 25, 2002) --
-- --
-- --
-- Copyright PoINT Software & Systems GmbH 1995-2002. All rights reserved. --
-- --
-- This software is proprietary to and embodies the confidential technology --
-- of PoINT Software & Systems GmbH. Possession, use, or copying of this --
-- software and media is authorized only pursuant to a valid written --
-- license from PoINT or an authorized sublicensor. --
==============================================================================
------------
Installation
------------
Installation in Windows 3.1x:
-----------------------------
This version of PoINT CDR Dlls do not work in Windows 3.1x and cannot
be installed on this platform.
Remark for installation in Windows 95/98/Me
-------------------------------------------
IMPORTANT !!
Please disable the 'auto. notification of media changes' (see control panel ->
system -> device manager -> CD-ROM -> <your recorder> -> properties -> setting).
RESTRICTION OF WINDOWS 95 !!
In older versions of Windows 95 (up to 4.00.950a) PoINT CDR Dlls can support
only one connected ATAPI drive. In case you are using one of these versions
and if you want to connect a CD-ROM drive and an additional CD recorder,
please connect both drives to the same IDE channel. Configure the CD-ROM
drive as IDE master and the recorder as IDE slave. PoINT CDR Dlls will then
find and support the recorder.
ASPI LAYER !!
ATAPI drives are fully supported in Windows 95/98/Me. Unfortunatelly some
software products install an incompatible ASPI manager which makes it
impossible to access ATAPI drives. In case that PoINT CDR Dlls does not
find ATAPI drives although available, please solve the problem by either
installing an ASPI update e.g. from Adaptec (
www.adaptec.com) or, in
extreme cases, install Windows 95/98/Me again over the existing installation
to replace incompatible by original modules.
USB DRIVES !!
PoINT CDR Dlls fully supports USB drives on Windows 98 and Windows Me
platforms. On Windows 95, USB drives are not supported.
FireWire (IEEE-1394) DRIVES !!
PoINT CDR Dlls fully supports FireWire drives on Windows 98 and Windows Me
platforms. On Windows 95, FireWire drives are not supported.
Installation in Windows NT 4:
-----------------------------
IMPORTANT !!
The standard CD-ROM driver of Windows NT 4.x up to and including service
pack 3 allocates and locks kernel memory during operation. With service pack
4, this problem has been solved by Microsoft.
Since this memory is never released, the system may fail if you record more
than one CD. There is no work-around for this problem on application level.
Therefore please replace the original CD-ROM driver of Windows NT 4 with
the driver which is delivered with CDR Dlls. The name of the original
driver is CDROM.SYS, it is located in C:\WINDOWS\SYSTEM32\DRIVERS. If you
want to restore the original driver at a later time, please make a backup
copy of this driver before you install CDR Dlls.
If you do not want to replace the original driver for any reason, please
disable the standard CD-ROM driver before you record your CDs. You may
find the driver in the control panel under devices, it's name is 'Cdrom'.
It is recommended to create a second configuration first, and to disable
the driver in this configuration.
USB DRIVES !!
Windows NT does not support USB.
FireWire (IEEE-1394) DRIVES !!
Windows NT does not support FireWire.
Remark for installation in Windows 2000
---------------------------------------
IMPORTANT !!
On systems with multiple processors, install service pack 2 or higher.
USB DRIVES !!
PoINT CDR Dlls supports USB drives on Windows 2000 platforms. Please note
that drive letters must be assigned to the drives, otherwise the drives
will not be recognised.
FireWire (IEEE-1394) DRIVES !!
PoINT CDR Dlls supports FireWire drives on Windows 2000 platforms. Please
note that drive letters must be assigned to the drives, otherwise the
drives will not be recognised.
----------------------------------------------------------------
Modifications compared to older versions of PoINT CDR Dlls
----------------------------------------------------------------
Version 2.7.022:
----------------
1) New recorders
PoINT CDR Dlls has been tested with the following recorders
- AOpen CRW2440
- _NEC CB-2100
- _NEC CD-RW NR-9100A
- _NEC NR-7800B
- _NEC NR-7900A
- Philips PCRW2010
- Pioneer DVD-RW DVR-104
- Plextor CD-R PX-W2410
- Plextor CD-R PX-W4012
- Plextor CD-R PX-320
- Yamaha CRW2200
- Yamaha CRW3200
Version 2.7.021:
----------------
1) Improvements
Some IDE driver implementations (esp. under Windows 2000) limit the
maximum data transfer size to 8 memory pages. This caused comuni-
cation errors in older versions. This version contains a work-
around for the problem.
2) New recorders
PoINT CDR Dlls have been tested with the following recorders
- NEC NR-7700A
- NEC NR-7800A
- NEC NR-8500A
- Plextor CD-R PX-W1610
Version 2.7.020:
----------------
1) Improvements
Starting with this release, PoINT CDR Dlls support buffer underrun
free recording (known as BURN Proof).
2) New recorders
PoINT CDR Dlls have been tested with the following recorders
- Generic CRD-BP4
- _NCR NR-7700A
- Pioneer DVD-RW DVR-103
- Sanyo CRD-BP4
- Teac CD-W512S
- Yamaha CRW2100
Version 2.7.019:
----------------
1) Improvements
Point CDR Dlls has been ported to and tested on Windows 2000 and
Windows Me platforms.
2) Improvements
Support for USB recorders in Windows 98 and Windows Me has
been added.
Version 2.7.018:
----------------
1) New recorders
Support for the following recorders has been added:
- _NCR NR-7500A
- Plextor CD-R PX-W1210
- Sanyo CRD-RW1
- Sanyo CRD-RW2
- Yamaha CRW8824
Version 2.7.017:
----------------
1) New recorders
Support for the following recorders has been added:
- Ricoh CD-R/RW MPxxxx
- Ricoh DVD/CDRW MPxxxx
Version 2.7.016:
----------------
1) New recorders
Support for the following recorders has been added:
- Sony CRX Family
2) Bug fix
Unfortunatelly the version 2.7.015 contained a bug which disabled
all Philips drives and Ricoh MP62xx (incl. all OEM models). This
has been corrected. Sorry!
Version 2.7.015:
----------------
1) New recorders
Support for the following recorders has been added:
- Plextor CD-R PX-W8432
- Plextor CD-R PX-W124
- Yamaha CRW8424
2) Improvements
The DAO implementation for ATAPI recorders has been improved. This
avoids 'drive not ready' and 'illegal command' error as you may
have seen them in older versions. This especially solves problems
with Yamaha's DAO implementation.
Version 2.7.014:
----------------
1) New recorders
Support for the following recorders has been added:
- HP CD-Writer+ 9xxx
- Mitsubishi CDVR-2X4
- Mitsumi CD-R CR-2401TS
- Yamaha CRW2216
- Yamaha CRW4261
- Yamaha CRW6416
2) Improvements
Support for drives which are only capable of the raw disc-at-once
mode has been added.
1) New recorders
The following new ATAPI drives are supported using the new RAW DAO mode:
HP CD-Writer+ 7xxx
IDE-CD ReWritable-2x2x6
IDE-CD R/RW 2x2x24
IOMEGA ZIP-CD
PHILIPS CDD3600
PHILIPS CDD3610
PHILIPS CDD3801
PHILIPS PCA382RW
Plexwriter 8 4 32A
Plexwriter 12 4 32
SCSI-CD ReWritable-2x2x6
TRAXDATA CDRW2224 PLUS
TRAXDATA CDRW2260+
TRAXDATA CRW2260 PRO
WAITEC WT2422
Support for the following recorders has been added in V2.6:
- Generic CRD-R800S
- Kodak CDR-240
- Mitsubishi CDVR-2X4
- Mitsumi CD-R CR-2401TS
- Plextor CD-R PX-W4220
- Plextor CD-R PX-W8220
- SAF CD-R8020
- Teac CD-R56S
- Teac CD-R58S
- Traxdata CDR6120
- WPI CDR-432
2) Improvements
CD-Rs can now be prepared for additional data session (e.g CD-EXTRA).
Please refer to the Recording Options dialogue and to the corresponding
online help for more information.
PoINT PoINT CDR Dlls can now record sound in pauses and especially supports
a long initial pause which may contain a hidden bonus track.
------------------------------
List of supported CD recorders
------------------------------
This version of PoINT CDR Dlls has been tested with the following recording
devices (DAO = disc-at-once). Please read also the comments below. For
an updated list, please refer to
www.pointsoft.de.
Remark:
This list does not always show the full name of the tested recorders, but
only the significant part of the name. Especially extensions like 'S' (SCSI),
'E' (EIDE), 'T' (TRAY), 'i' (internal), 'e' (external) are often ommitted.
Only in case that specific versions are not supported, the exact extension
of the supported versions is shown.
- Acer CRW620
- Acer CRW620A
- AOpen CRW2440
- Generic CRD-BP4 (see Sanyo CRD-BP4)
- Generic CRD-R800S (see Sanyo CRD-R800S)
- Grundig CDR100IPW
- HighTech CD-R1002
- HP 4020I
- HP 6020I
- HP CD-Writer+ 7100i/e (see below !)
- HP CD-Writer+ 72xxi/e (see below !)
- HP CD-Writer+ 8xxxi (see below !)
- HP CD-Writer+ 9xxx
- IDE-CD R/RW
- IDE-CD ReWritable
- IOMEGA ZIPCD
- IOMEGA ZIP CD
- JVC XR-W1001 (not DAO)
- JVC XR-W2001 (firmware revision 2.xx for DAO)
- JVC XR-W2010
- JVC XR-W2020
- JVC XR-W2022
- JVC R2626
- JVC XR-W2040
- Lite-On LTR-511
- Kodak PCD200 (not DAO)
- Kodak PCD225 (firmware revision 1.07 or higher for DAO)
- Kodak PCD240 (see below)
- Matsushita CW-7501
- Matsushita CW-7502
- Mitsubishi CDRW226
- Mitsubishi CDRW226A
- _NEC CB-2100
- _NEC CD-RW NR-9100A
- _NEC NR-7500A
- _NEC NR-7700A
- _NEC NR-7800A
- _NEC NR-7800B
- _NEC NR-7900A
- _NEC NR-8500A
- Nomai 680RW
- Olympus CDS615
- Olympus CDS620
- Optima CD-R650
- Philips CDD521 (not DAO)
- Philips CDD522 (firmware revision 1.07 or higher for DAO)
- Philips CDD2000
- Philips CDD2600
- Philips CDD3600
- Philips CDD3610
- Philips CDD3801
- Philips OMNIWRITER26
- Philips PCA382RW
- Philips PCRW2010
- Pioneer DR-R504 (not DAO)
- Pioneer DVD-R DVD-R7322
- Pioneer DVD-RW DVR-103
- Pioneer DVD-RW DVR-104
- Pinnacle RCD-1000 (firmware revision 2.xx for DAO)
- Pinnacle RCD5040
- Pinnacle RCD4X4
- Pinnacle RCDW226
- Plasmon RF4000 (not DAO)
- Plasmon RF4100 (not DAO)
- Plasmon RF4102 (not DAO)
- Plasmon CDR4220
- Plasmon CDR4240 (see below !)
- Plasmon CDR4400
- Plasmon CDR480 (firmware revision 3.00 or higher)
- Plextor CD-R PX-R412 (firmware revision 1.03 higher for DAO)
- Plextor CD-R PX-R820
- Plextor CD-R PX-W4220
- Plextor CD-R PX-W8220
- Plextor CD-R PX-W8432
- Plextor CD-R PX-W124
- Plextor CD-R PX-W1210
- Plextor CD-R PX-W1610
- Plextor CD-R PX-W2410
- Plextor CD-R PX-W4012
- Plextor CD-R PX-320
- Ricoh CD-R/RW MPxxxx
- Ricoh DVD/CDRW MPxxxx
- Ricoh MP6200A
- Ricoh MP6200S
- Ricoh MP6201S
- Ricoh MP6201S
- Ricoh RO-1420 (see below !)
- SAF CD-R2004
- SAF CD-R2006 (not DAO)
- SAF CD-R4006 (see below !)
- SAF CD-R8020
- Sanyo CRD-BP4
- Sanyo CRD-R800S
- Sanyo CRD-RW1
- Sanyo CRD-RW2
- SCSI-CD ReWritable
- Sony CDU920
- Sony CDU924
- Sony CDU926 (not DAO)
- Sony CDU928 (not DAO, see below !)
- Sony CDU948
- Sony CRX Family
- Teac CD-R50S
- Teac CD-R55S (firmware revision 1.0f or higher for DAO)
- Teac CD-R56S (includes all variants like 400 and 600)
- Teac CD-R58S
- Teac CD-W512S
- Traxdata CDR4120
- Traxdata CDR6120
- Traxdata CDRW2224 PLUS
- Traxdata CDRW2260
- Traxdata CDRW2260+
- Traxdata CDRW4260
- Traxdata CDRW4424 (not DAO)
- Traxdata CRW2260 PRO
- Waitec WT2036EI (not DAO)
- Waitec WT2422
- Waitec WT2444 (not DAO)
- Waitec WT4046
- Waitec WT412
- Yamaha CDR100 (firmware revision 1.04 or higher for DAO)
- Yamaha CDR102
- Yamaha CDR200
- Yamaha CDR400 (see below !)
- Yamaha CRW2100
- Yamaha CRW2200
- Yamaha CRW2216
- Yamaha CRW2260
- Yamaha CRW3200
- Yamaha CRW4260
- Yamaha CRW4261
- Yamaha CRW4416
- Yamaha CRW6416
- Yamaha CRW8424
- Yamaha CRW8824
-------------------------------
Specific comments/restrictions:
-------------------------------
- Grundig CDR100IPW,
HP 4020I,
Philips CDD2000,
Plasmon CDR4220
Firmware revision 1.20 does not support sub-indexes and
reverses the audio channels; use revison 1.25 or above;
this revision can be obtained from Philips
(philips.com in the world wide web)
- JVC XR-W1001,
JVC XR-W2001,
Pinnacle RCD-1000
Those JVC drives which do not support DAO write all tracks
at once; therefore no link blocks (no errors or noise) is
added between audio tracks; only between lead-in area and
first track and between last track and lead-out area link
blocks are inserted; link blocks at these positions normally
do not cause errors and the resulting discs are perfect
Catalog numbers (UPC/EAN) and ISRC are not supported by
these drives
- JVC XR-W2010,
Pinnacle RCD5040
Catalog numbers (UPC/EAN) and ISRC are not supported by
these drives.
- Kodak PCD225,
Philips CDD522
Firmware revisions 1.04 to 1.06 theoretically support DAO
recording, too, but in practise it does not work reliably;
therefore drives with these firmware revisions should not
be used at all
- HP 7100i/e
7100i is an ATAPI drive.
7100e is connected to the printer port of a PC. This drive
drive did not work reliably at 2x speed during our tests.
Please check carefully the performance of your system by
simulating the recording of several disks at 2x speed. In
case that problems occur, record at 1x speed.
The drives do not allow to modify the length of pauses at
the beginning of tracks in track-at-once mode. The default
length is 2 seconds.
- HP 72xxi/e
72xxi is an ATAPI drive.
72xxe is connected to the printer port of a PC. If you use
this drive, please check carefully the performance of your
system by simulating the recording of several disks at 2x
speed. In case that problems occur, record at 1x speed.
The drives do neither support DAO, nor do they allow to
modify the length of pauses at the beginning of tracks.
The default length is 2 seconds.
- HP 8xxxi
The HP 8xxxi drives are ATAPI drives.
The drives do neither support DAO, nor do they allow to
modify the length of pauses at the beginning of tracks.
The default length is 2 seconds.
- HP 9xxx
The drives do neither support DAO, nor do they allow to
modify the length of pauses at the beginning of tracks.
The default length is 2 seconds.
- _NEC NR-7500A
This drive does not support sub-indexes and cannot record
more than about 90 tracks in disc-at-once mode.
- Philips CDD3600,
Philips CDD3610,
Philips CDD3801,
Philips PCA382RW,
IDE-CD R/RW,
IDE-CD ReWritable,
IOMEGA ZIPCD,
IOMEGA ZIP CD,
SCSI-CD ReWritable,
Traxdata CDRW2260+,
Traxdata CRW2260 PRO,
Traxdata CDRW2224 PLUS,
Traxdata CDRW4424,
Waitec WT2036EI,
Waitex WT2422,
Waitex WT2444
The drives do not allow to modify the length of pauses at
the beginning of tracks in track-at-once mode. The default
length is 2 seconds.
- Matsushita CW-7501,
Plasmon CDR4240
These drives do not correctly disconnect from the SCSI bus
during recording.
- Ricoh RO-1420
This drive does not correctly disconnect from the SCSI bus
during recording.
Furthermore RO-1420 does not support copy protection bits
(see on-line help). Copy protection will always be on.
- Sanyo CRD-BP4
The drive does not support sub-indexes on audio CDs.
- Sony CDU920,
Sony CDU924,
HighTech CD-R1002,
Olympus CDS615,
Olympus CDS620,
Optima CD-R650,
SAF CD-R2004,
Sony CDU948
Catalog numbers (UPC/EAN) and ISRC are not supported by
these drives
- Sony CDU928
This drive does not support DAO, but it allows to vary the
lengths of pauses. However, even if the length is set to 0,
2 run-out blocks are always added between subsequent tracks.
Additionally, the current versions of the drive do not
work under Windows NT.
- SAF CD-R4006,
Yamaha CDR400
The comments below are valid for firmware revision 1.0a
only. In firmware revision 1.0b or above, all of these
problems are solved.
With firmware 1.0a, these drives do not disconnect from the
SCSI bus during writing. Thus, the SCSI bus is permanently
claimed by the drives, communication with other connected
drives cannot take place. In other words, these drives must
be connected to a separate SCSI adapter. DO NOT connect any
other drive to the same bus. Otherwise writing will not be
reliable because Windows forces hard resets on the SCSI bus
if the other drives do not respond. PoINT CDR Dlls prints
"Drive not ready" in this case.
With firmware 1.0a, ISRC codes and catalog numbers (UPC/EAN)
are not correctly recorded by the drives.
- Yamaha CDR100,
Plasmon CDR4400
Firmware revision 1.08 adds noise to the end of the last
audio track; either set the copy protection bit for all
tracks or try to get a new firmware revision to avoid
the click noise
- Acer CRW620,
Acer CRW620A,
AOpen CRW2440,
Generic CRD-BP4,
Generic CRD-R800S,
HP 6020,
JVC XR-W2020,
JVC XR-W2022,
JVC R2626,
JVC XR-W2040,
Lite-On LTR-511
Matsushita CW-7502,
Mitsubishi CDRW226,
Mitsubishi CDRW226A,
_NEC CB-2100,
_NEC CD-RW NR-9100A,
_NEC NR-7700A,
_NEC NR-7800A,
_NEC NR-7800B,
_NEC NR-7900A,
_NEC NR-8500A,
Nomai 680RW,
Panasonic CW-7502,
Philips CDD2600,
Philips OMNIWRITER26
Philips PCRW2010,
Pinnacle RCD4X4,
Pinnacle RCDW226,
Pioneer DR-R504,
Pioneer DVD-R DVD-R7322,
Pioneer DVD-RW DVR-103,
Pioneer DVD-RW DVR-104,
Plasmon CDR480,
Plextor CD-R PX-R412,
Plextor CD-R PX-W4220,
Plextor CD-R PX-R820,
Plextor CD-R PX-W8220,
Plextor CD-R PX-W8432A,
Plextor CD-R PX-W124,
Plextor CD-R PX-W1210,
Plextor CD-R PX-W1610,
Plextor CD-R PX-W2410,
Plextor CD-R PX-W4012,
Plextor CD-R PX-320,
Ricoh CD-R/RW MPxxxx,
Ricoh DVD/CDRW MPxxxx,
Ricoh MP6200A,
Ricoh MP6200S,
Ricoh MP6201S,
SAF CD-R2006,
SAF CD-R8020,
Sanyo CRD-R800S,
Sanyo CRD-RW1,
Sanyo CRD-RW2,
Sony CDU926,
Sony CRX Family,
Teac CD-R50S,
Teac CD-R55S,
Teac CD-R56S,
Teac CD-R58S,
Teac CD-W512S,
Traxdata CDR4120,
Traxdata CDR6120,
Traxdata CDRW2260,
Traxdata CDRW4260,
Waitec WT4046,
Waitec WT412,
Yamaha CDR102,
Yamaha CDR200,
Yamaha CRW2100,
Yamaha CRW2200,
Yamaha CRW2216,
Yamaha CRW2260,
Yamaha CRW3200,
Yamaha CRW4260,
Yamaha CRW4261,
Yamaha CRW4416,
Yamaha CRW6416,
Yamaha CRW8424,
Yamaha CRW8824
No restrictions or comments