硬件

这话放后面有三个卡农输出接口。用于人声录音的话  哪一个更合适一些。接上都可以出声。

(3) FRONT END DIRECT OUTPUT "DIRECT OUT"
Conventional three pin male XLR connector providing balanced, line level output directly from the
front-end amplifiers (MIC, LINE, DI). This output is configured before the EQ, Compressor, De-esser,
and main outputs. This direct output is essentially equivalent to the output on an HV-3 micamp and
can be used in addition to the main outputs (below). Pin 1 is ground. Pin 2 is positive polarity. Pin 3 is
negative polarity. This line level output is capable of driving <600 ohm loads and long, high capacitance
cables. Outputs may be configured in an unbalanced configuration by grounding pin 3, or taking pin 2
directly as an unbalanced signal while floating pin 3. In the former configuration, the output is automatically
increased by 6 dB. Connector contacts are Neutrik Galvatronic gold plated. It is suggested that XLR
cable connectors used with the STT-1 employ identical plating.
(4) MAIN OUTPUT #1 "MAIN OUT - BAL"
Conventional three pin male XLR connector providing balanced, line level output from all stages of the
STT-1. Can be used simultaneously with all other outputs. Pin 1 is ground. Pin 2 is positive polarity. Pin
3 is negative polarity. This monolithic-based, balanced line level output is capable of driving <600 ohm
loads and long, high capacitance cables and has a maximum output level of +32 dBu. Outputs may be
configured in an unbalanced pin-2-hot configuration by either grounding pin 3, or taking pin 2 directly
as an unbalanced signal while floating pin 3. In the latter configuration, the output is decreased by 6 dB

(5) MAIN OUTPUT #2 "MAIN OUT - UNBAL"
Conventional three pin male XLR connector providing unbalanced, line level output from all stages
of the STT-1. Can be used simultaneously with all other outputs. This XLR sits directly above the 1/4"
unbalanced output connector. Pin 1 is ground. Pin 2 is positive polarity. Pin 3 is ground. This output is
all discrete, pure Class-A, and is capable of driving < 600 ohm loads and long, high capacitance cables.
This output should drive a balanced destination with no interface concerns. In the rare instance where a
balanced destination exhibits difficulty with an unbalanced source, use the balanced output (#4 above).
Connector contacts are Neutrik Galvatronic gold plated. It is suggested that XLR cable connectors used
with the STT-1 employ identical plating.
(6) MAIN OUTPUT #3 "MAIN OUT - UNBAL"
Conventional 1/4" female phone connector providing unbalanced, line level output from all stages of the
STT-1. Can be used simultaneously with all other outputs. Tip is signal positive polarity, Sleeve is ground.
This output is all-discrete, pure Class-A and is capable of driving < 600 ohm loads and long, high capacitance
cables. This output should drive a balanced destination with no interface concerns. In the rare instance
where a balanced destination shows difficulty with an unbalanced source, use the balanced output
(#4 above). This output is paralleled with Output #5 (above).
(7) DYNAMICS LINK "Dyn Link"
Conventional RCA-style phono jack providing a connection to the dynamics side chain circuit. Use to
link dual STT-1 units for stereo operation. Any conventional RCA phono cable should work appropriately.
(8) EARTH/AUDIO GROUND JUMPER
A barrier terminal which ties earth ground to audio ground. If ground "hum" loops are experienced when
using the STT-1, removing this jumper may help. Using this jumper to lift ground, the integrity of the
chassis/earth ground connection is never compromised. Do not defeat the earth grounding pin on the AC
plug.

美莲娜 St-1官方说明书， 第一句的开场白， 耐人寻味。

Dedicated to the lives, memory, and families of
Chris Camacho and Gabe Weiner — two young men
who shared a passion for great audio,
and who left us much too soon.

Gabe 1970-1997
Chris 1959-1999

第一个

那应该是带LIINK那个字样的输出。

特别好的话放